あなたはIT職員ですか。成功したいのですか。成功したいのならPass4TestのJuniperのJN0-521試験トレーニング資料を利用してください。当社の資料は実践の検証に合格したもので、あなたが首尾よくIT認証試験に合格することを助けます。Pass4TestのJuniperのJN0-521トレーニング資料を手に入れたらあなたはIT業種でもっとよい昇進を持つようになり、高レベルのホワイトカラーのトリートメントを楽しむこともできます。あなたはまだ何を心配しているのですか。Pass4TestのJuniperのJN0-521トレーニング資料はあなたのニーズを満たすことができますから、躊躇わずにPass4Testを選んでください。Pass4Testはあなたと苦楽を共にして、一緒に挑戦に直面します。
Pass4TestのJuniperのJN0-521試験トレーニング資料は最高のトレーニング資料です。あなたはIT職員としたら、Pass4Testはあなたが選ばなくてはならないトレーニング資料です。Pass4TestのJuniperのJN0-521試験トレーニング資料は絶対に信頼できるもので、IT認証を受ける受験生を対象として特別に研究された問題と解答に含まれているう資料です。 JuniperのJN0-521試験に受かるのはIT職員の皆さんの目標です。Pass4Testの合格率は信じられないほど高いです。Pass4Testはあなたの成功にずっと力を尽くしています。
専門的に言えば、試験を受けるに関するテクニックを勉強する必要があります。Pass4Testというサイトは素晴らしいソースサイトで、JuniperのJN0-521の試験材料、研究材料、技術材料や詳しい解答に含まれています。問題集が提供したサイトは近年で急速に増加しています。あなたは試験の準備をするときに見当もつかないかもしれません。Pass4TestのJuniperのJN0-521試験トレーニング資料は専門家と受験生の皆様に証明された有効なトレーニング資料で、あなたが試験の合格することを助けられます。
JuniperのJN0-521認定試験はIT業界の中でとても普遍的な試験になります。試験の準備は時間とエネルギーがかかります。時は金なり社会に時間を無駄しないようによいツルを探し出されるのはみんなの希望です。Pass4TestのJuniperのJN0-521認証試験の問題集は君の20時間だけかかりますよ。
Pass4Testが提供した教育資料は真実のテストに非常に近くて、あなたが弊社の短期の特殊訓練問題を通じてすぐにIT専門の知識を身につけられます。弊社は君の試験の１００％合格率を保証いたします。
試験番号：JN0-521問題集
試験科目：Juniper 「FWV.Associate (JNCIA-FWV)」
購入前にお試し,私たちの試験の質問と回答のいずれかの無料サンプルをダウンロード：http://www.pass4test.jp/JN0-521.html
NO.1 Which statement accurately describes the "config rollback" feature?
A.Once the "config rollback" feature is enabled, it allows the administrator to re-apply a previously saved
configuration file from flash.
B.The "config rollback" feature is enabled by default, it allows the administrator to re-apply a previously
saved configuration file from flash.
C.Once the "config rollback" feature is enabled, it allows the administrator to re-apply a locked
configuration file from a separate area in flash.
D.Once the "config rollback" feature is enabled, it allows the administrator to revert to the prior ScreenOS
image or configuration file in the event an upgrade operation aborts.
Answer: C
Juniper参考書 JN0-521練習問題 JN0-521 JN0-521認定試験 JN0-521
NO.2 You are configuring an interface in the untrust zone with an IP address, telnet enabled, and WebUI
management.
Which sequence of steps must be performed to make the interface operational at the end of the
configuration sequence?
A.Assign the interface to a zone, define the IP address, enable Web and telnet services.
B.Assign the interface to a zone, define the IP address, accept default management services.
C.Assign the interface to a virtual router, define the IP address, enable Web and telnet services.
D.Assign the interface to a zone, define the IP address, define a manage IP address, accept default
management services.
Answer: A
Juniper過去問 JN0-521 JN0-521過去問 JN0-521 JN0-521認定証
NO.3 What is the purpose of the "Permitted IP" address on a ScreenOS device?
A.It defines a list of addresses that are trusted to perform management on the ScreenOS device.
B.It is used in policy rules to determine which user traffic is allowed through the ScreenOS device.
C.It defines which range of addresses that can access devices connected to the ScreenOS device.
D.It is the address that an external device uses to gain management access to a ScreenOS device.
Answer: A
Juniper認定資格 JN0-521 JN0-521 JN0-521問題集
NO.4 Which statement is correct regarding administrator privileges?
A.Any administrator can change their privileges on an as-needed basis.
B.Administrator privileges can only be established and changed by the root administrator.
C.Administrator privileges can be established and changed by the root and all-privilege administrator.
D.Administrator privileges can only be established by the root and can be changed by the root and
all-privilege administrator.
Answer: B
Juniper JN0-521 JN0-521認証試験 JN0-521
NO.5 Which command is used when configuring web management on the VLAN1 interface for a client
connected to an e3 interface in the DMZ zone?
A.set int eth3 manage web
B.set zone v1-dmz manage web
C.set int dmz zone manage web
D.set int VLAN1 zone dmz manage web
Answer: B
Juniper認証試験 JN0-521 JN0-521
NO.6 Which command would you run to check IPSec Phase 1 active status?
A.get sa
B.get event 427
C.get sa active
D.get ike cookie
Answer: D
Juniper JN0-521認定証 JN0-521問題集 JN0-521
NO.7 Click the Exhibit button.
In the exhibit, which interface would be used to forward traffic to host 1.1.7.5?
A.e0/1
B.e0/2
C.e0/3
D.e0/4
Answer: C
Juniper JN0-521練習問題 JN0-521問題集 JN0-521認定試験
NO.8 When changes are made to the running config during a WebUI management session, to what external
hardware component can the changes be saved?
A.FTP server
B.TFTP server
C.PC local disk
D.Compact Flash Card
Answer: C
Juniper JN0-521参考書 JN0-521 JN0-521参考書 JN0-521
NO.9 Which type of NAT is performed when you implement interface-based NAT?
A.source IP address translation
B.destination IP address translation
C.source IP and port address translation
D.destination IP and port address translation
Answer: C
Juniper認定資格 JN0-521 JN0-521 JN0-521参考書
NO.10 What will change the root admin password?
A.set admin password
B.set root-admin password
C.set admin password
D.set admin user password
Answer: A
Juniper練習問題 JN0-521認定資格 JN0-521問題集 JN0-521参考書
NO.11 By default, where are changes stored when a save command is issued from the CLI during a
management session?
A.NVRAM
B.internal flash
C.PCMCIA card
D.Compact Flash Card
Answer: B
Juniper JN0-521過去問 JN0-521 JN0-521認定試験
NO.12 What is the purpose of the "Manage-IP" address on a ScreenOS device?
A.It defines a list of addresses that are trusted to perform management on the ScreenOS device.
B.It is used in policy rules to determine which device is allowed to manage the ScreenOS device.
C.It is the address that an external device uses to gain management access to a ScreenOS device.
D.It defines a list of device addresses that can manage the ScreenOS device without being authenticated
prior to session establishment.
Answer: C
Juniper JN0-521 JN0-521
NO.13 A ScreenOS firewall has the correct interfaces addressed and active. A policy is written allowing
interzone FTP traffic from a directly connected client. But the traffic does not cross the firewall from the
client to the server.
What is the most likely problem with the firewall?
A.The ScreenOS firewall has no physical connection to the FTP server.
B.The ALG option on the ScreenOS firewall has not been enabled for FTP traffic.
C.The ScreenOS firewall does not have a route defined to the FTP servers' subnet.
D.The ScreenOS firewall does not have a route defined to the FTP clients subnet.
Answer: C
Juniper JN0-521 JN0-521認定試験 JN0-521認定試験 JN0-521認証試験
NO.14 In the packet forwarding decision process, how is the second packet handled differently than the first
in a series of allowed interzone packets?
A.The second packet causes an ARP query.
B.The second packet is checked against the policy table.
C.The second packet is forwarded without a sanity check.
D.The second packet is forwarded without checking the route table.
Answer: D
Juniper JN0-521 JN0-521 JN0-521参考書
NO.15 Which process describes how an addressed physical interface is moved into a Layer 2 zone?
A.Place the required interface into the VLAN zone.
B.Place the required interface into L2 zones such as V1-Trust, V1-Untrust
C.Remove the interface from the L3 zone such as Trust and place it into a L2 zone such as V1-Trust
D.Remove the address from the interface, remove the interface from the L3 zone, and then place
interface in the L2 zone.
Answer: D
Juniper問題集 JN0-521 JN0-521 JN0-521認定試験 JN0-521問題集
NO.16 What are two benefits of configuring a ScreenOS device in transparent mode? (Choose two.)
A.There is no need to reconfigure the IP addresses of routers or protected servers.
B.There is no need to create MIPs or VIPs for incoming traffic to reach protected servers.
C.Policies are easier to create since you do not have to include source and destination IP addresses.
D.The product can support more VPNs and obtain greater throughput because there is less overhead to
manage.
Answer: AB
Juniper JN0-521認定証 JN0-521 JN0-521
NO.17 What is the purpose of the VLAN1 interface?
A.It provides policy-based NAT for 802.1Q VLANs.
B.It provides an interface that can be used with 802.1Q VLANs in transparent mode.
C.It provides the ScreenOS device with a routable IP address while operating in route mode.
D.It provides an interface that can be used to remotely manage the ScreenOS device while operating in
transparent mode.
Answer: D
Juniper JN0-521 JN0-521問題集 JN0-521練習問題
NO.18 Click the Exhibit button.
In the exhibit, which two forms of address translation would have generated the output shown? (Choose
two.)
A.MIP
B.NAT-src with no DIP
C.Interface-based translation
D.NAT-src with a DIP, fixed-port disabled
Answer: BC
Juniper認定証 JN0-521 JN0-521 JN0-521
NO.19 When a firewall receives the first packet in a series, what will it immediately do?
A.Check its route table.
B.Check its session table.
C.Determine if traffic is crossing zones.
D.Verify that it is not malformed or a fragment.
Answer: D
Juniper JN0-521認定試験 JN0-521
NO.20 You are looking at the event log of the responding device and it says,
"Rejected an initial Phase 1 packet from an unrecognized peer gateway"
What are three likely reasons for the failure? (Choose three.)
A.The peer ID is misconfigured.
B.The default gateway is missing.
C.The preshare keys are mismatched.
D.The gateway address is misconfigured.
E.The outgoing interface is misconfigured.
Answer: ADE
Juniper JN0-521過去問 JN0-521認定証 JN0-521認定証 JN0-521
NO.21 Which two statements are true in regards to a ScreenOS firewall in transparent mode? (Choose two.)
A.VPNs can terminate to the VLAN1 interface IP address.
B.Static routes must be configured if multiple virtual routers are going to be used.
C.It can be installed in a network without the requirement to reconfigure IP addressing schemes.
D.You must use the console port to manage the device as you cannot manage the device using an
Ethernet port.
Answer: AC
Juniper JN0-521 JN0-521練習問題
NO.22 Which ScreenOS WebUI button reorders policies?
A.Shift
B.Move
C.Reorder
D.Transfer
Answer: B
Juniper認証試験 JN0-521過去問 JN0-521 JN0-521
NO.23 In the command, save config from tftp 1.1.7.250 abcd.cfg merge, which function does the merge
parameter specify?
A.The config file from the TFTP server will replace the configuration in RAM.
B.The config file from the TFTP server will replace the startup configuration file in internal flash.
C.The merge parameter is not valid for TFTP files, it is only valid for configuration files stored in internal
flash.
D.The config file from the TFTP server will be combined with the configuration file in RAM and the
combined result will be saved in internal flash.
Answer: D
Juniper JN0-521練習問題 JN0-521練習問題
NO.24 When managing a ScreenOS device using the WebUI and performing an image upgrade, from which
hardware component will the ScreenOS image be loaded?
A.TFTP server
B.PC local disk
C.internal flash
D.Compact Flash Card
Answer: B
Juniper JN0-521 JN0-521練習問題 JN0-521認定試験
NO.25 When performing an image upgrade using the CLI, which three locations would be a source for this
image? (Choose three.)
A.FTP server
B.TFTP server
C.internal flash
D.PC local disk
E.Compact Flash Card
Answer: BCE
Juniper認定試験 JN0-521 JN0-521 JN0-521認定証 JN0-521過去問 JN0-521過去問
NO.26 A ScreenOS firewall is running in transparent mode. The firewall receives a packet which has no entry
in its forwarding table.
What will the firewall do?
A.Flood out all ports.
B.Check its route table for interzone destination.
C.Perform a policy lookup to determine the interfaces to which the source address is permitted, and flood
the packet out of those interfaces.
D.Perform a policy lookup to determine the zones to which the source address is permitted, and flood the
packet out the interfaces bound to those zones.
Answer: D
Juniper認定証 JN0-521 JN0-521過去問
NO.27 When configuring a firewall in a critical environment where a local backup configuration is quickly
needed, what should be completed on a periodic basis?
A.Execute exec config rollback.
B.Execute save config to last-known-good.
C.Execute save regularly or create a script that does this.
D.Execute save software from flash to pcmcia .
Answer: B
Juniper認定資格 JN0-521 JN0-521認定証
NO.28 By default, from which hardware component is the startup copy of the ScreenOS loaded?
A.NVRAM
B.TFTP server
C.internal flash
D.PCMCIA card
Answer: C
Juniper JN0-521 JN0-521認定証
NO.29 An operational firewall needs a configuration loaded and executed while it is passing user data.
Which CLI command will perform this process without interrupting traffic?
A.save config from tftp 1.1.7.250 15June06.cfg to flash
B.save config from tftp 1.1.7.250 15June06.cfg to ram
C.save config from tftp 1.1.7.250 15June06.cfg merge
D.save config from tftp 1.1.7.250 15June06.cfg to flash
Answer: C
Juniper認定試験 JN0-521問題集 JN0-521 JN0-521認定証 JN0-521認定資格
NO.30 Telnet management has been enabled on an interface in the untrust zone.
What else should be completed to limit telnet access to the ScreenOS device from trusted management
PCs?
A.Define a permitted IP address.
B.Define a policy from trust to untrust.
C.Define a trusted IP in the address table.
D.Define a manage IP address on this interface.
Answer: A
Juniper参考書 JN0-521 JN0-521認定証 JN0-521過去問
Pass4Testは専門的なIT認証サイトで、成功率が１００パーセントです。これは多くの受験生に証明されたことです。Pass4TestにはIT専門家が組み立てられた団体があります。彼らは受験生の皆さんの重要な利益が保障できるように専門的な知識と豊富な経験を活かして特別に適用性が強いトレーニング資料を研究します。その資料が即ちJuniperのJN0-521試験トレーニング資料で、問題集と解答に含まれていますから。
没有评论:
发表评论