高品質のHP HP0-P10「HP Integrity Server Multi-OS Installation and Deployment」問題集

この情報の時代の中に、たくさんのIT機構はHPのHP0-P10認定試験に関する教育資料がありますけれども、受験生がこれらのサイトを通じて詳細な資料を調べられなくて、対応性がなくて受験生の注意 に惹かれなりません。

IT業種は急激に発展しているこの時代で、IT専門家を称賛しなければならないです。彼らは自身が持っている先端技術で色々な便利を作ってくれます。それに、会社に大量な人的·物的資源を節約させると同時に、案外のうまい効果を取得しました。彼らの給料は言うまでもなく高いです。そのような人になりたいのですか。羨ましいですか。心配することはないです。Pass4TestのHPのHP0-P10トレーニング資料はあなたに期待するものを与えますから。Pass4Testを選ぶのは、成功を選ぶということになります。

君はまずネットで無料なHPのHP0-P10試験問題をダウンロードしてから 弊社の品質を確信してから、購入してください。Pass4Testは提供した商品は君の成功を全力で助けさしたげます。

試験番号：HP0-P10問題集

試験科目：HP 「HP Integrity Server Multi-OS Installation and Deployment」

Pass4TestのHPのHP0-P10トレーニング資料を利用したら、初めて試験を受けるあなたでも一回で試験に合格できることを保証します。Pass4TestのHPのHP0-P10トレーニング資料を利用しても合格しないのなら、我々は全額で返金することができます。あなたに他の同じ値段の製品を無料に送って差し上げます。

購入前にお試し,私たちの試験の質問と回答のいずれかの無料サンプルをダウンロード：http://www.pass4test.jp/HP0-P10.html

NO.1 Which Management Processor (MP) command displays the physical location information of the
system?
A. SI
B. ID
C. LOC
D. SO
Answer: B

HP認証試験   HP0-P10過去問   HP0-P10   HP0-P10認証試験

NO.2 Which command in the iLO 2 controls access permissions for an Integrity rx6600 server?
A. PS
B. SO
C. PC
D. SD
Answer: B

HP   HP0-P10   HP0-P10

NO.3 The system is not responding normally. You have access to the Management Processor (MP). Which
command do you use to cycle the power?
A. ps
B. pc
C. rs
D. co
Answer: B

HP参考書   HP0-P10   HP0-P10認定証

NO.4 Where is the diagnostic panel on an Integrity rx4640 server located?
A. top
B. front
C. back
D. left side
E. right side
Answer: A

HP過去問   HP0-P10参考書   HP0-P10   HP0-P10過去問   HP0-P10認定証

NO.5 Which capability does the Management Processor (MP) in the Integrity rx2620 server provide?
A. offline hardware monitoring
B. hardware administration and management
C. remote HP-UX operating system installation
D. remote monitoring of server room conditions
Answer: B

HP認定試験   HP0-P10   HP0-P10   HP0-P10認定資格

NO.6 You must back up all your Integrity server NVRAM configurations. Which backup utility is available for
download that can be used in the EFI shell?
A. bcfg
B. getmtc
C. nvrambkp
D. bcknvram
Answer: C

HP認定試験   HP0-P10認定資格   HP0-P10過去問   HP0-P10   HP0-P10

NO.7 Where does HP OpenVMS store all error information?
A. /var/adm/syslog/syslog.log
B. SYS$ERRLOG:SYSTEM.LOG
C. SYS$ERRORLOG:ERRLOG.SYS
D. SYS$MANAGER:OPERATOR.LOG
Answer: C

HP認証試験   HP0-P10   HP0-P10認証試験   HP0-P10練習問題   HP0-P10

NO.8 What is the difference between a Machine Check Abort (MCA) and a Transfer of Control (TOC)?
A. An MCA is a software dump; a TOC is a hardware register dump.
B. An MCA is a hardware register dump; a TOC initiates a software dump.
C. An MCA dump is for Windows systems; a TOC is for HP-UX systems.
D. An MCA dump is for HP-UX systems; a TOC is for Windows systems.
Answer: B

HP過去問   HP0-P10   HP0-P10   HP0-P10認定試験   HP0-P10

NO.9 You have run an Offline Diagnostics Environment (ODE) utility. What should you do before booting
the operating system or running any non-ODE utility?
A. Reset the system at the MP:CM> prompt.
B. Use the MP:CM> poff command to power off the DC voltage.
C. Reset the system at the EFI shell prompt and disconnect the AC power for one minute.
D. Reset the system at the EFI shell prompt, use the MP:CM> pc command to power off DC voltage, and
disconnect the AC power for one minute.
Answer: A

HP練習問題   HP0-P10   HP0-P10参考書   HP0-P10認定資格

NO.10 Which command do you use in the EFI Shell to verify that an Integrity rx4640 server has the latest
firmware?
A. openinfo fw
B. info fw
C. ver fw
D. sysrev
Answer: B

HP練習問題   HP0-P10過去問   HP0-P10   HP0-P10

NO.11 What does an amber blinking System LED on an Integrity rx2620 indicate?
A. System is in error state
B. Remote access is enabled
C. A system warning
D. Management Processor is powered off
Answer: C

HP   HP0-P10認定試験   HP0-P10   HP0-P10認定資格

NO.12 You are managing an Integrity rx2620 server that is located in a remote office. Which Management
Processor (MP) console command do you use to gather the state of the system and LEDs?
A. LED
B. VFP
C. ERRDUMP D. SYSSTAT
Answer: B

HP   HP0-P10   HP0-P10問題集

NO.13 How can you determine the firmware version that is running on an HP Integrity system? (Select two.)
A. At the EFI Boot Manager menu, open the EFI shell and enter info fw.
B. At the MP main menu, open the Command Menu (cm) and enter firmware.
C. At the EFI Boot Manager menu, go to the Firmware menu and select Version.
D. At the EFI Boot Manager menu, go to the Firmware Configuration menu and select Version.
E. If you access the EFI Boot Manager menu using iLO, the firmware versions display automatically.
Answer: AE

HP   HP0-P10   HP0-P10   HP0-P10

NO.14 Which Offline Diagnostics Environment (ODE) utility should you use to test the memory of an Integrity
server?
A. MAPPER
B. SYSDIAG
C. MEMDIAG
D. DIMMDIAG
Answer: C

HP   HP0-P10認定試験   HP0-P10過去問   HP0-P10認定証   HP0-P10過去問

NO.15 How can you access the UUID on an entry-level HP Integrity server? (Select two.)
A. The UUID is written on the system information label of the server.
B. At the EFI Boot Manager menu, access the EFI Shell; then enter info sys.
C. At the Management Processor (MP) main menu, go to the Command Menu and enter id.
D. At the EFI Boot Manager menu, access the System Configuration menu and select System UUID.
E. If you access the EFI Boot Manager menu using integrated Lights-Out (iLO), the UUID displays
automatically.
Answer: AB

HP認証試験   HP0-P10   HP0-P10   HP0-P10   HP0-P10   HP0-P10認定試験

NO.16 After you replace a memory module on an Integrity server, how do you clear the entries in the Page
Deallocation Table (PDT)?
A. Interrupt the boot, go to the Service Menu and enter pdt clear.
B. Interrupt the boot, go to the EFI shell, and then enter pdt clear.
C. Interrupt the boot, enter the MP:CM> CL command, and choose PDT.
D. After reboot, the system automatically deletes entries in the PDT without user input.
Answer: B

HP   HP0-P10認証試験   HP0-P10   HP0-P10認定資格

NO.17 You replaced failed hardware in an HP Integrity server. Which steps should you perform to ensure
that the system is operational?
A. Verify that the replaced hardware is visible in the EFI Shell, and that the Diagnostic LEDs are clear.
B. Verify that the replaced hardware is visible in the EFI Shell and that the correct firmware version is
loaded.
C. From the EFI Shell, boot the system. From within the operating system, confirm that the replaced
hardware is functioning and verify the correct status of the Diagnostic LEDs.
D. Verify that the replaced hardware is visible in the EFI Shell and that the correct firmware version is
loaded. Then boot the system and confirm that the replaced hardware is functioning.
Answer: D

HP参考書   HP0-P10   HP0-P10認証試験

NO.18 Which methods of accessing the Offline Diagnostics Environment (ODE) utilities does HP recommend?
(Select two.)
A. from the HP service partition
B. from the EFI Boot Menu
C. from the MP command menu
D. from the operating system disk
E. from the Offline Diagnostic Utility CD
Answer: AE

HP   HP0-P10   HP0-P10認証試験   HP0-P10   HP0-P10練習問題

NO.19 Which front panel LEDs on an Integrity rx2620 can indicate an error?
A. Locator LED and System LED
B. Power LED and Diagnostic LEDs
C. System LED and Diagnostic LEDs
D. Diagnostic LEDs and Locator LED
Answer: C

HP認証試験   HP0-P10参考書   HP0-P10   HP0-P10

NO.20 In a Linux environment, what is one of the components used to manage highly available solutions
offered by Virtual Server Environment (VSE)?
A. HP Workload Manager
B. HP OpenView Node Manager
C. HP Global Workload Manager
D. Performance Management Pack
Answer: C

HP   HP0-P10参考書   HP0-P10認定証

NO.21 The rx3600 and rx6600 have LEDs which show the FRU Health status. How can you view the state of
these LEDs remotely?
A. From the MP main menu, select VFP
B. From the MP main menu, select SL
C. From the MP main menu, select CM, then LS
D. From the MP main menu, select CM, then DF
Answer: A

HP   HP0-P10   HP0-P10   HP0-P10認定資格

NO.22 Which Offline Diagnostics Environment (ODE) utility should you use to test processors on an Integrity
server?
A. WDIAG
B. IA64DIAG
C. CPUDIAG
D. PROCDIAG
Answer: C

HP練習問題   HP0-P10   HP0-P10認証試験

NO.23 You want to load new firmware for the Management Processor (MP). Which command do you use to
verify a proper connection to an FTP server?
A. xd
B. bin
C. scp
D. xu
Answer: A

HP認証試験   HP0-P10   HP0-P10   HP0-P10認定証

NO.24 You need to perform a maintenance task on a Management Processor module. Which command
displays a list of connected users?
A. who
B. list
C. usmgr
D. show user
Answer: A

HP   HP0-P10練習問題   HP0-P10   HP0-P10   HP0-P10   HP0-P10

NO.25 You just installed an Integrity rx2620 server. How do you set the MP and system times?
A. Use the MP date command to set time and date.
B. The time will be set automatically during system boot.
C. Use the EFI shell command time to set time and date of the MP.
D. Use the MP date command to set the date, and use the MP time command to set the time.
Answer: C

HP   HP0-P10   HP0-P10   HP0-P10

NO.26 You have limited access to the Management Processor (MP), but you have full access to the system
Baseboard Management Console (BMC). Which command do you issue in the BMC Command Line
Interface (CLI) to power off the system hardware?
A. cli> p 0
B. cli> rs 1
C. cli> pc 0
D. cli> loc 0
Answer: A

HP過去問   HP0-P10認定資格   HP0-P10   HP0-P10認定試験   HP0-P10認証試験

NO.27 Which Offline Diagnostics Environment (ODE) utility should you use to test an HP Tachyon XL2 Fibre
Channel card?
A. IODIAG
B. FCDIAG
C. PERFVER
D. FCFUPDATE
Answer: A

HP認定資格   HP0-P10   HP0-P10   HP0-P10練習問題   HP0-P10参考書   HP0-P10練習問題

NO.28 The diagnostic panel on an Integrity rx4640 shows a fan failure. What information on the Management
Processor (MP) shows you when the fan failed?
A. MP:CM> PS
B. MP:CM> SS
C. MP> SL --> L - Live Events
D. MP> SL --> E - System Event
Answer: D

HP   HP0-P10過去問   HP0-P10

NO.29 From the EFI Boot Manager, how can you get information about the installed memory DIMMs?
A. Go to the EFI Shell and enter: info mem
B. It is not possible to get the information offline.
C. The information displays automatically at the EFI Boot Manager menu.
D. Go to the System Configuration menu and choose Memory Configuration.
Answer: A

HP   HP0-P10   HP0-P10   HP0-P10   HP0-P10認定試験

NO.30 An Integrity rx2620 server with Windows Server 2003 is running terminal services but has stopped
responding. Which MP command do you use to shut down gracefully and power off the server?
A. rs -g
B. pc -g
C. rs -off
D. pc -off
Answer: B

HP   HP0-P10   HP0-P10認定試験   HP0-P10認定証   HP0-P10過去問   HP0-P10

HPのHP0-P10認定試験を受けることを決めたら、Pass4Testがそばにいて差し上げますよ。Pass4Testはあなたが自分の目標を達成することにヘルプを差し上げられます。あなたがHPのHP0-P10認定試験に合格する需要を我々はよく知っていますから、あなたに高品質の問題集と科学的なテストを提供して、あなたが気楽に認定試験に受かることにヘルプを提供するのは我々の約束です。